KC868-A series and Uair Smart Controller
Threads
- What makes the ESP32 chip better over the older ESP8266? (0 Replies)
- A16 and HC-SR04 (1 Reply)
- KCS: Add ability to turn off saving output state to NVS? (7 Replies)
- A64 turn off (1 Reply)
- A16 -> TX RX pins (1 Reply)
- A128 and B32Pro (5 Replies)
- KCS firmware (14 Replies)
- Lesson23- How to connect RGB LED strip using ESP32 by KC868-A4 A8 (18 Replies)
- using KC868-A16 ESP32 relays at 220v (1 Reply)
- KC868-A16 & ds18b20 (11 Replies)
- KC868-A6 DS1307 Issue (20 Replies)
- PIR Sensor A6 (1 Reply)
- how to check PCF8574/PCF8575 i2c address (0 Replies)
- Pulse Counter Sensor (0 Replies)
- KC868-A16S or KC868-A8S (5 Replies)
- KC868 A6 User Guide (11 Replies)
- communication with I2C sensor (3 Replies)
- KC868-A16 esp32 board (A16)as upgrade of a Homevision Controller? (36 Replies)
- Lesson20- how to use PCF8574 IIC extend GPIO for ESP32 input ports (2 Replies)
- Kinkony A24. Digital input (5 Replies)
- Help with KC868-A8 and traditional wall switch (8 Replies)
- Lesson18- how to use UDP communication with KC868-A8 by ethernet (4 Replies)
- KC868-AI TCP COMUNICATION PROTOCOL (1 Reply)
- kc868_A8: NodeMCU-32s, 80Mhz, 115200. None. Disabled sur COM4. (9 Replies)
- KC868-A8S v2 manufacture issue? print issue? Tasmota issue? (1 Reply)
- Technical consultation connection KC868-A16 (18 Replies)
- Tuto for NOOBS (1 Reply)
- 1wire stopped working - KC868-A8 (7 Replies)
- how to replace ESP32 large memory module for KinCony ESP32 Controller (0 Replies)
- Error on ESPHOME Official Config? (5 Replies)
- Problem uploasing esphome firmware to KC868-A16 (3 Replies)
- KC868-AI - from Alarm panel (1 Reply)
- KC868-A16S Analog input 4-20mA convert not linear (3 Replies)
- KC868-A8 + KCS + iiC + PCF8574 + TUYA (3 Replies)
- KC868-A4 USB not detected by computer (1 Reply)
- KC868 AK (3 Replies)
- KC868-A8 - Possible to use A1 and A2 as standard inputs? (1 Reply)
- KC868-A16S Analog input 4-20mA connection (4 Replies)
- output turns off automaticly (1 Reply)
- No Response (3 Replies)
- Smoke Sensor Connected to KC868-AI (1 Reply)
- RS485 Light Switch (7 Replies)
- Kc868-AK (3 Replies)
- KC868-HAv2 (1 Reply)
- KC-868-A8 analog output 0-10v (1 Reply)
- KC868 AI (9 Replies)
- how to compile new tasmota firmware by simplest way (1 Reply)
- Help to choose the right board (3 Replies)
- Two IFTT on same Input (1 Reply)
- KC868-A64 REV 1.3 - Ethernet is not Working (3 Replies)