Smart Home Automation Forum
H32B and H16B Digital input - Printable Version

+- Smart Home Automation Forum (https://www.kincony.com/forum)
+-- Forum: Technical Support (https://www.kincony.com/forum/forumdisplay.php?fid=1)
+--- Forum: KC868-HxB series Smart Controller (https://www.kincony.com/forum/forumdisplay.php?fid=2)
+--- Thread: H32B and H16B Digital input (/showthread.php?tid=1755)

Pages: 1 2

H32B and H16B Digital input - Dm81 - 03-16-2022

If device is in Client mode, why I don't receive any kind of string (hex, ansistring or else) on my server if digital input change state?
with COLB I receive the string about any input changes
thank you

RE: H32B and H16B Digital input - admin - 03-17-2022

Note: if want to use alarm message function, you must let your ethernet and wifi work mode=”TCP Server”, “UDP” can’t work for this function. Both ethernet and wifi need set work mode to “TCP Server”.
[Image: alarm-config.png]

RE: H32B and H16B Digital input - Dm81 - 03-17-2022

(03-17-2022, 12:12 AM)admin Wrote: Note: if want to use alarm message function, you must let your ethernet and wifi work mode=”TCP Server”, “UDP” can’t work for this function. Both ethernet and wifi need set work mode to “TCP Server”.
[Image: alarm-config.png]

ok, it works only in server mode otherwise in MQTT mode
what is the maximum voltage that the digital input can support?
thank you

RE: H32B and H16B Digital input - admin - 03-17-2022

for H32B/H16B , digital input MAX 3.3V
for H32BS, digital input MAX 12v.

RE: H32B and H16B Digital input - Dm81 - 04-02-2022

(03-17-2022, 10:55 AM)admin Wrote: for H32B/H16B , digital input MAX 3.3V
for H32BS, digital input MAX 12v.

Hello
I tested Digital input on H32B (device is set in tcp server mode) and I received message "RELAY-ALARM-x,OK",
I have some questions: (I used a contact to test it)
  •     why I receive message but after few seconds or more?
  •     when input change status again (contact is reopen) why I don't receive a message?


thank you in advance

RE: H32B and H16B Digital input - admin - 04-03-2022

1. do you have hold on about 1 second for "input" and GND?
2. how many time you released "input" with GND, re trigger again?

RE: H32B and H16B Digital input - Dm81 - 04-03-2022

(04-03-2022, 12:20 AM)admin Wrote: 1. do you have hold on about 1 second for "input" and GND?
2. how many time you released "input" with GND, re trigger again?

  1. yes I do
  2. I try to release input between 1 second and more and more seconds but no message received from server of H32B about "allarm off"
I read here (https://www.kincony.com/smart-controller-development-protocol.html) that the device doesn't send message at status changes about "alarm", is it correct? if yes, is it an error?
thak you

 

RE: H32B and H16B Digital input - admin - 04-03-2022

when you need feedback alarm message from TCP, make sure your ethernet and wifi work mode both = "TCP" , no one have set by UDP.
we will upload new firmware for KC868-H32B, that when input and GND released, will send a "DISALARM" message.

RE: H32B and H16B Digital input - admin - 04-03-2022

here is new firmware of KC868-H32B: https://www.kincony.com/forum/showthread.php?tid=1802
you can update, it's suitable for you.

RE: H32B and H16B Digital input - Dm81 - 04-03-2022

(04-03-2022, 08:09 AM)admin Wrote: here is new firmware of KC868-H32B: https://www.kincony.com/forum/showthread.php?tid=1802
you can update, it's suitable for you.

thank you very much
is this works also for H16B?