+- Smart Home Automation Forum (https://www.kincony.com/forum)
+-- Forum: Technical Support (https://www.kincony.com/forum/forumdisplay.php?fid=1)
+--- Forum: KC868-A series and Uair Smart Controller (https://www.kincony.com/forum/forumdisplay.php?fid=6)
+--- Thread: output turns off automaticly (/showthread.php?tid=5703)
output turns off automaticly - deibar - 05-06-2024
Hello, I have two Kincony A16 boards. Im using toggle buttons, but after some time output automatically turns off, and this happens with both Kincony boards with every output, wiring is good, what can be the reason? This how the code looks like:
esphome:
name: esphome-web-af6e50
friendly_name: Kincony2
esp32:
board: esp32dev
framework:
type: arduino
# Example configuration entry for ESP32
i2c:
sda: 4
scl: 5
scan: true
id: bus_a
# Enable logging
logger:
# Enable Home Assistant API
api:
encryption:
key: "pbLoAOpRUI49e65b0pCUrVShaclU3bM38vlGfnNQ9YY="
ota:
wifi:
ssid: !secret wifi_ssid
password: !secret wifi_password
# Enable fallback hotspot (captive portal) in case wifi connection fails
ap:
ssid: "Esphome-Web-Af6E50"
password: "ajhfwy1kFdbc"
captive_portal:
# Example configuration entry
pcf8574:
- id: 'pcf8574_output1' # for output channel 1-8
address: 0x24
- id: 'pcf8574_output2' # for output channel 9-16
address: 0x25
- id: 'pcf8574_input1' # for input channel 1-8
address: 0x22
- id: 'pcf8574_input2' # for input channel 9-16
address: 0x21
esphome:
name: esphome-web-b050e4
friendly_name: Kincony1
esp32:
board: esp32dev
framework:
type: arduino
# Example configuration entry for ESP32
i2c:
sda: 4
scl: 5
scan: true
id: bus_a
# Enable logging
logger:
# Enable Home Assistant API
api:
encryption:
key: "tBC8hXDhMHsgklwFmZerS9tVQP0p+6Qus3+OyUTj+Jo="
ota:
wifi:
ssid: !secret wifi_ssid
password: !secret wifi_password
# Enable fallback hotspot (captive portal) in case wifi connection fails
ap:
ssid: "Esphome-Web-B050E4"
password: "SziFua377JQb"
captive_portal:
# Example configuration entry
pcf8574:
- id: 'pcf8574_output1' # for output channel 1-8
address: 0x24
- id: 'pcf8574_output2' # for output channel 9-16
address: 0x25
- id: 'pcf8574_input1' # for input channel 1-8
address: 0x22
- id: 'pcf8574_input2' # for input channel 9-16
address: 0x21
# Outputs
switch:
- platform: gpio
id: livingroom
name: "Living room "
pin:
pcf8574: pcf8574_output2
number: 7
mode: OUTPUT
inverted: true
# Inputs
binary_sensor:
- platform: gpio
name: "Living room switch"
pin:
pcf8574: pcf8574_input1
number: 0
mode: INPUT
inverted: true
on_press:
then:
- switch.toggle: livingroom
RE: output turns off automaticly - admin - 05-06-2024
ESPHome config yaml you can use this one: https://www.kincony.com/forum/showthread.php?tid=1628
take a photo of your whole board wire, board, power supply and load. maybe some hardware problem if you are using the ymal link given you.