<![CDATA[Smart Home Automation Forum - KC868-1U]]> https://www.kincony.com/forum/ Sat, 11 Apr 2026 09:36:20 +0000 MyBB <![CDATA[KC868-1U connect with extend relay diagram]]> https://www.kincony.com/forum/showthread.php?tid=3030 Fri, 30 Jun 2023 08:54:33 +0800 admin]]> https://www.kincony.com/forum/showthread.php?tid=3030
.jpg   kc868-1u-diagram.jpg (Size: 382.5 KB / Downloads: 1087) ]]>
.jpg   kc868-1u-diagram.jpg (Size: 382.5 KB / Downloads: 1087) ]]> <![CDATA[[Arduino source code for KC868-1U]-07_RS485]]> https://www.kincony.com/forum/showthread.php?tid=3010 Wed, 21 Jun 2023 13:22:25 +0800 KinCony Support]]> https://www.kincony.com/forum/showthread.php?tid=3010 [Arduino source code for KC868-1U]-07_RS485
Code:
/*KC868-1U  RS485 CODE*/
#define RS485RX  32
#define RS485TX  33
void setup() {
  Serial.begin(115200);
  Serial2.begin(115200,SERIAL_8N1,A2_RS485RX,A2_RS485TX);

   Serial2.println("RS485 SEND is OK!!");
   Serial2.println("******************");
 
}

void loop() {
  /*print the received data of RS485 port*/
  while(Serial2.available()>0)
   {
    Serial2.print((char)Serial2.read());//Read rs485 receive data  and print it
   }
  delay(200);
}
]]> [Arduino source code for KC868-1U]-07_RS485
Code:
/*KC868-1U  RS485 CODE*/
#define RS485RX  32
#define RS485TX  33
void setup() {
  Serial.begin(115200);
  Serial2.begin(115200,SERIAL_8N1,A2_RS485RX,A2_RS485TX);

   Serial2.println("RS485 SEND is OK!!");
   Serial2.println("******************");
 
}

void loop() {
  /*print the received data of RS485 port*/
  while(Serial2.available()>0)
   {
    Serial2.print((char)Serial2.read());//Read rs485 receive data  and print it
   }
  delay(200);
}
]]> <![CDATA[[Arduino source code for KC868-1U]-06_OUTPUT]]> https://www.kincony.com/forum/showthread.php?tid=3009 Wed, 21 Jun 2023 13:22:13 +0800 KinCony Support]]> https://www.kincony.com/forum/showthread.php?tid=3009 [Arduino source code for KC868-1U]-06_OUTPUT
Code:
/*KC868-1U PCF8574 digital output code*/
#include "Arduino.h"
#include "PCF8574.h"

// Set i2c address
PCF8574 pcf8574_OUT1(0x24,4,16);


void setup()
{
    Serial.begin(115200);
//    delay(1000);

    // Set pinMode to OUTPUT
    pcf8574_OUT1.pinMode(P0, OUTPUT);
  pcf8574_OUT1.pinMode(P1, OUTPUT);
  pcf8574_OUT1.pinMode(P2, OUTPUT);
  pcf8574_OUT1.pinMode(P3, OUTPUT);
  pcf8574_OUT1.pinMode(P4, OUTPUT);
  pcf8574_OUT1.pinMode(P5, OUTPUT);
  pcf8574_OUT1.pinMode(P6, OUTPUT);
  pcf8574_OUT1.pinMode(P7, OUTPUT);
 
   pcf8574_OUT1.begin();
 
    


}

void loop()
{
  for(int i=0;i<=7;i++){
    pcf8574_OUT1.digitalWrite(i, LOW);
    delay(1000);
  }
  for(int i=0;i<=7;i++){
    pcf8574_OUT1.digitalWrite(i, HIGH);
    delay(1000);
  }
 
}
]]> [Arduino source code for KC868-1U]-06_OUTPUT
Code:
/*KC868-1U PCF8574 digital output code*/
#include "Arduino.h"
#include "PCF8574.h"

// Set i2c address
PCF8574 pcf8574_OUT1(0x24,4,16);


void setup()
{
    Serial.begin(115200);
//    delay(1000);

    // Set pinMode to OUTPUT
    pcf8574_OUT1.pinMode(P0, OUTPUT);
  pcf8574_OUT1.pinMode(P1, OUTPUT);
  pcf8574_OUT1.pinMode(P2, OUTPUT);
  pcf8574_OUT1.pinMode(P3, OUTPUT);
  pcf8574_OUT1.pinMode(P4, OUTPUT);
  pcf8574_OUT1.pinMode(P5, OUTPUT);
  pcf8574_OUT1.pinMode(P6, OUTPUT);
  pcf8574_OUT1.pinMode(P7, OUTPUT);
 
   pcf8574_OUT1.begin();
 
    


}

void loop()
{
  for(int i=0;i<=7;i++){
    pcf8574_OUT1.digitalWrite(i, LOW);
    delay(1000);
  }
  for(int i=0;i<=7;i++){
    pcf8574_OUT1.digitalWrite(i, HIGH);
    delay(1000);
  }
 
}
]]> <![CDATA[[Arduino source code for KC868-1U]-05_LAN8720_UDP]]> https://www.kincony.com/forum/showthread.php?tid=3008 Wed, 21 Jun 2023 13:21:59 +0800 KinCony Support]]> https://www.kincony.com/forum/showthread.php?tid=3008 [Arduino source code for KC868-1U]-05_LAN8720_UDP
Code:
#include <ETH.h>
#include <WiFiUdp.h>

#define ETH_ADDR        0
#define ETH_POWER_PIN  -1
#define ETH_MDC_PIN    23
#define ETH_MDIO_PIN   18  
#define ETH_TYPE       ETH_PHY_LAN8720
#define ETH_CLK_MODE   ETH_CLOCK_GPIO17_OUT

WiFiUDP Udp;                      //Create UDP object
unsigned int localUdpPort = 4196; //local port

// Set it based on the IP address of the router
IPAddress local_ip(192, 168, 1, 200);
IPAddress gateway(192, 168, 1, 1);
IPAddress subnet(255, 255, 255, 0);
IPAddress dns(192, 168, 1, 1);

void setup()
{
  Serial.begin(115200);
  Serial.println();
  
  ETH.begin(ETH_ADDR, ETH_POWER_PIN, ETH_MDC_PIN, ETH_MDIO_PIN, ETH_TYPE, ETH_CLK_MODE); //start with ETH

  // write confir for static IP, gateway,subnet,dns1,dns2
  if (ETH.config(local_ip, gateway, subnet, dns, dns) == false) {
    Serial.println("LAN8720 Configuration failed.");
  }else{Serial.println("LAN8720 Configuration success.");}
 
/* while(!((uint32_t)ETH.localIP())) //wait for IP
  {

  }*/
  Serial.println("Connected");
  Serial.print("IP Address:");
  Serial.println(ETH.localIP());

  Udp.begin(localUdpPort); //begin UDP listener
}

void loop()
{
  int packetSize = Udp.parsePacket(); //get package size
  if (packetSize)                     //if have received data
  {
    char buf[packetSize];
    Udp.read(buf, packetSize); //read current data

    Serial.println();
    Serial.print("Received: ");
    Serial.println(buf);
    Serial.print("From IP: ");
    Serial.println(Udp.remoteIP());
    Serial.print("From Port: ");
    Serial.println(Udp.remotePort());

    Udp.beginPacket(Udp.remoteIP(), Udp.remotePort()); //ready to send data
    Udp.print("Received: ");   
    Udp.write((const uint8_t*)buf, packetSize); //copy data to sender buffer
    Udp.endPacket();            //send data
  }
}
]]> [Arduino source code for KC868-1U]-05_LAN8720_UDP
Code:
#include <ETH.h>
#include <WiFiUdp.h>

#define ETH_ADDR        0
#define ETH_POWER_PIN  -1
#define ETH_MDC_PIN    23
#define ETH_MDIO_PIN   18  
#define ETH_TYPE       ETH_PHY_LAN8720
#define ETH_CLK_MODE   ETH_CLOCK_GPIO17_OUT

WiFiUDP Udp;                      //Create UDP object
unsigned int localUdpPort = 4196; //local port

// Set it based on the IP address of the router
IPAddress local_ip(192, 168, 1, 200);
IPAddress gateway(192, 168, 1, 1);
IPAddress subnet(255, 255, 255, 0);
IPAddress dns(192, 168, 1, 1);

void setup()
{
  Serial.begin(115200);
  Serial.println();
  
  ETH.begin(ETH_ADDR, ETH_POWER_PIN, ETH_MDC_PIN, ETH_MDIO_PIN, ETH_TYPE, ETH_CLK_MODE); //start with ETH

  // write confir for static IP, gateway,subnet,dns1,dns2
  if (ETH.config(local_ip, gateway, subnet, dns, dns) == false) {
    Serial.println("LAN8720 Configuration failed.");
  }else{Serial.println("LAN8720 Configuration success.");}
 
/* while(!((uint32_t)ETH.localIP())) //wait for IP
  {

  }*/
  Serial.println("Connected");
  Serial.print("IP Address:");
  Serial.println(ETH.localIP());

  Udp.begin(localUdpPort); //begin UDP listener
}

void loop()
{
  int packetSize = Udp.parsePacket(); //get package size
  if (packetSize)                     //if have received data
  {
    char buf[packetSize];
    Udp.read(buf, packetSize); //read current data

    Serial.println();
    Serial.print("Received: ");
    Serial.println(buf);
    Serial.print("From IP: ");
    Serial.println(Udp.remoteIP());
    Serial.print("From Port: ");
    Serial.println(Udp.remotePort());

    Udp.beginPacket(Udp.remoteIP(), Udp.remotePort()); //ready to send data
    Udp.print("Received: ");   
    Udp.write((const uint8_t*)buf, packetSize); //copy data to sender buffer
    Udp.endPacket();            //send data
  }
}
]]> <![CDATA[[Arduino source code for KC868-1U]-04_IR_send_code]]> https://www.kincony.com/forum/showthread.php?tid=3007 Wed, 21 Jun 2023 13:19:57 +0800 KinCony Support]]> https://www.kincony.com/forum/showthread.php?tid=3007 [Arduino source code for KC868-1U]-04_IR_send_code
Code:
/*if download key pressed  send IR signal*/
#include <IRremote.h>
IRsend irsend(5);     
uint8_t sRepeats = 0;

void setup() {

  Serial.begin(115200);
  pinMode(0,INPUT);
  IrSender.begin(5,0);
  IrSender.enableIROut(38);
}

void loop() {
    
        Serial.println("Turn on LED");
        irsend.sendNECRaw(0xF807FF00, sRepeats);   //  0xF807FF00  is the raw_code  of led on
        delay(1000);
        Serial.println("Turn off LED");
        irsend.sendNECRaw(0xF906FF00, sRepeats);  //   0xF906FF00 is the raw_code  of led Off
       
}  
]]> [Arduino source code for KC868-1U]-04_IR_send_code
Code:
/*if download key pressed  send IR signal*/
#include <IRremote.h>
IRsend irsend(5);     
uint8_t sRepeats = 0;

void setup() {

  Serial.begin(115200);
  pinMode(0,INPUT);
  IrSender.begin(5,0);
  IrSender.enableIROut(38);
}

void loop() {
    
        Serial.println("Turn on LED");
        irsend.sendNECRaw(0xF807FF00, sRepeats);   //  0xF807FF00  is the raw_code  of led on
        delay(1000);
        Serial.println("Turn off LED");
        irsend.sendNECRaw(0xF906FF00, sRepeats);  //   0xF906FF00 is the raw_code  of led Off
       
}  
]]> <![CDATA[[Arduino source code for KC868-1U]-03_IR_receive_code]]> https://www.kincony.com/forum/showthread.php?tid=3006 Wed, 21 Jun 2023 13:19:38 +0800 KinCony Support]]> https://www.kincony.com/forum/showthread.php?tid=3006 [Arduino source code for KC868-1U]-03_IR_receive_code
Code:
/*KC868-1U IR receive code*/
#include <IRremote.h>
IRrecv irrecv (15);
void setup() {

  Serial.begin(115200);
  irrecv.enableIRIn();
}

void loop() {
    if (irrecv.decode()) {
      Serial.print("irCode address: ");           
        Serial.println(irrecv.decodedIRData.address,HEX);
        Serial.print("irCode command: ");           
        Serial.println(irrecv.decodedIRData.command,HEX);
        Serial.print("irCode decodedRawData: ");           
        Serial.println(irrecv.decodedIRData.decodedRawData,HEX);
        Serial.println();
        //delay(1000);
    }
      IrReceiver.resume();
}
]]> [Arduino source code for KC868-1U]-03_IR_receive_code
Code:
/*KC868-1U IR receive code*/
#include <IRremote.h>
IRrecv irrecv (15);
void setup() {

  Serial.begin(115200);
  irrecv.enableIRIn();
}

void loop() {
    if (irrecv.decode()) {
      Serial.print("irCode address: ");           
        Serial.println(irrecv.decodedIRData.address,HEX);
        Serial.print("irCode command: ");           
        Serial.println(irrecv.decodedIRData.command,HEX);
        Serial.print("irCode decodedRawData: ");           
        Serial.println(irrecv.decodedIRData.decodedRawData,HEX);
        Serial.println();
        //delay(1000);
    }
      IrReceiver.resume();
}
]]> <![CDATA[[Arduino source code for KC868-1U]-02_INPUT]]> https://www.kincony.com/forum/showthread.php?tid=3005 Wed, 21 Jun 2023 13:19:25 +0800 KinCony Support]]> https://www.kincony.com/forum/showthread.php?tid=3005 [Arduino source code for KC868-1U]-02_INPUT
Code:
/*KC868-1U Digital input code*/
#include "Arduino.h"
#include "PCF8574.h"

// Set i2c address
PCF8574 pcf8574_IN1(0x22,4,16);

void setup()
{
    Serial.begin(115200);
    delay(1000);

pcf8574_IN1.pinMode(P0, INPUT);
pcf8574_IN1.pinMode(P1, INPUT);
pcf8574_IN1.pinMode(P2, INPUT);
pcf8574_IN1.pinMode(P3, INPUT);
pcf8574_IN1.pinMode(P4, INPUT);
pcf8574_IN1.pinMode(P5, INPUT);
pcf8574_IN1.pinMode(P6, INPUT);
pcf8574_IN1.pinMode(P7, INPUT);

    pcf8574_IN1.begin();


}

void loop()
{
uint8_t val1 = pcf8574_IN1.digitalRead(P0);
uint8_t val2 = pcf8574_IN1.digitalRead(P1);
uint8_t val3 = pcf8574_IN1.digitalRead(P2);
uint8_t val4 = pcf8574_IN1.digitalRead(P3);
uint8_t val5 = pcf8574_IN1.digitalRead(P4);
uint8_t val6 = pcf8574_IN1.digitalRead(P5);
uint8_t val7 = pcf8574_IN1.digitalRead(P6);
uint8_t val8 = pcf8574_IN1.digitalRead(P7);
 
if (val1==LOW) Serial.println("KEY1 PRESSED");
if (val2==LOW) Serial.println("KEY2 PRESSED");
if (val3==LOW) Serial.println("KEY3 PRESSED");
if (val4==LOW) Serial.println("KEY4 PRESSED");
if (val5==LOW) Serial.println("KEY5 PRESSED");
if (val6==LOW) Serial.println("KEY6 PRESSED");
if (val7==LOW) Serial.println("KEY7 PRESSED");
if (val8==LOW) Serial.println("KEY8 PRESSED");

    delay(300);
}
]]> [Arduino source code for KC868-1U]-02_INPUT
Code:
/*KC868-1U Digital input code*/
#include "Arduino.h"
#include "PCF8574.h"

// Set i2c address
PCF8574 pcf8574_IN1(0x22,4,16);

void setup()
{
    Serial.begin(115200);
    delay(1000);

pcf8574_IN1.pinMode(P0, INPUT);
pcf8574_IN1.pinMode(P1, INPUT);
pcf8574_IN1.pinMode(P2, INPUT);
pcf8574_IN1.pinMode(P3, INPUT);
pcf8574_IN1.pinMode(P4, INPUT);
pcf8574_IN1.pinMode(P5, INPUT);
pcf8574_IN1.pinMode(P6, INPUT);
pcf8574_IN1.pinMode(P7, INPUT);

    pcf8574_IN1.begin();


}

void loop()
{
uint8_t val1 = pcf8574_IN1.digitalRead(P0);
uint8_t val2 = pcf8574_IN1.digitalRead(P1);
uint8_t val3 = pcf8574_IN1.digitalRead(P2);
uint8_t val4 = pcf8574_IN1.digitalRead(P3);
uint8_t val5 = pcf8574_IN1.digitalRead(P4);
uint8_t val6 = pcf8574_IN1.digitalRead(P5);
uint8_t val7 = pcf8574_IN1.digitalRead(P6);
uint8_t val8 = pcf8574_IN1.digitalRead(P7);
 
if (val1==LOW) Serial.println("KEY1 PRESSED");
if (val2==LOW) Serial.println("KEY2 PRESSED");
if (val3==LOW) Serial.println("KEY3 PRESSED");
if (val4==LOW) Serial.println("KEY4 PRESSED");
if (val5==LOW) Serial.println("KEY5 PRESSED");
if (val6==LOW) Serial.println("KEY6 PRESSED");
if (val7==LOW) Serial.println("KEY7 PRESSED");
if (val8==LOW) Serial.println("KEY8 PRESSED");

    delay(300);
}
]]> <![CDATA[[Arduino source code for KC868-1U]-01_DS18B20]]> https://www.kincony.com/forum/showthread.php?tid=3004 Wed, 21 Jun 2023 13:19:03 +0800 KinCony Support]]> https://www.kincony.com/forum/showthread.php?tid=3004 [Arduino source code for KC868-1U]-01_DS18B20
Code:
#include <DS18B20.h>

DS18B20 ds1(14); 
void setup() {
  Serial.begin(115200);

}
void loop() {
      Serial.printf("Tem1 is %.2f C \n ",ds1.getTempC());
}
]]> [Arduino source code for KC868-1U]-01_DS18B20
Code:
#include <DS18B20.h>

DS18B20 ds1(14); 
void setup() {
  Serial.begin(115200);

}
void loop() {
      Serial.printf("Tem1 is %.2f C \n ",ds1.getTempC());
}
]]> <![CDATA[KC868-1U configure yaml for ESPhome Home assistant]]> https://www.kincony.com/forum/showthread.php?tid=2999 Wed, 21 Jun 2023 09:23:51 +0800 admin]]> https://www.kincony.com/forum/showthread.php?tid=2999
.png   1U-ha.png (Size: 130.1 KB / Downloads: 809)

.txt   KC868-1U-ha-config.txt (Size: 5.76 KB / Downloads: 434)

esphome:
  name: 1u
  platform: ESP32
  board: esp32dev
 
 
remote_receiver:
  pin: 13
  dump:
    - rc_switch
  tolerance: 50%
  filter: 250us
  idle: 2ms
  buffer_size: 2kb
# Example configuration entry for ESP32
i2c:
  sda: 4
  scl: 16
  scan: true
  id: bus_a
# Example configuration entry
ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO17_OUT
  phy_addr: 0
  # Optional manual IP
 # manual_ip:
 #   static_ip: 192.168.1.199
#    gateway: 192.168.1.1
#    subnet: 255.255.255.0  
# Example configuration entry
pcf8574:
  - id: 'pcf8574_hub_out_1'  # for output channel 1-8
    address: 0x24
  - id: 'pcf8574_hub_in_1'  # for input channel 1-8
    address: 0x22
# Individual outputs
switch:
  - platform: gpio
    name: "light1"
    id: light1
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 0
      mode: OUTPUT
      inverted: true
  - platform: gpio
    name: "light2"
    id: light2
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 1
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light3"
    id: light3
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 2
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light4"
    id: light4
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 3
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light5"
    id: light5
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 4
      mode: OUTPUT
      inverted: true      
     
  - platform: gpio
    name: "light6"
    id: light6
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 5
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light7"
    id: light7
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 6
      mode: OUTPUT
      inverted: true
  - platform: gpio
    name: "light8"
    id: light8
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 7
      mode: OUTPUT
      inverted: true
binary_sensor:
  - platform: gpio
    name: "input1"
    on_press:
      then:
        - switch.toggle: light1
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 0
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input2"
    on_press:
      then:
        - switch.toggle: light2
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 1
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input3"
    on_press:
      then:
        - switch.toggle: light3
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 2
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input4"
    on_press:
      then:
        - switch.toggle: light4
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 3
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input5"
    on_press:
      then:
        - switch.toggle: light5
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 4
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input6"
    on_press:
      then:
        - switch.toggle: light6
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 5
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input7"
    on_press:
      then:
        - switch.toggle: light7
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 6
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input8"
    on_press:
      then:
        - switch.toggle: light8
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 7
      mode: INPUT
      inverted: true
  - platform: remote_receiver
    name: "remoter1"
    rc_switch_raw:
      code: '001111010111001010111000'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light1
    filters:
      - delayed_off: 200ms
  - platform: remote_receiver
    name: "remoter2"
    rc_switch_raw:
      code: '001111010111001010111100'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light2
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter3"
    rc_switch_raw:
      code: '001111010111001010110100'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light3
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter4"
    rc_switch_raw:
      code: '001111010111001010111001'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light4
    filters:
      - delayed_off: 200ms  
   
  - platform: remote_receiver
    name: "remoter5"
    rc_switch_raw:
      code: '001111010111001010110010'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light5
    filters:
      - delayed_off: 200ms
  - platform: remote_receiver
    name: "remoter6"
    rc_switch_raw:
      code: '001111010111001010110101'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light6
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter7"
    rc_switch_raw:
      code: '001111010111001010110001'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light7
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter8"
    rc_switch_raw:
      code: '001111010111001010110011'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light8
    filters:
      - delayed_off: 200ms
     
# Enable logging
logger:
# Enable Home Assistant API
api:
dallas:
  - pin: 14
    update_interval: 5s
sensor:
  - platform: dallas
    address: 0xa538cee908646128
    name: "1U Temperature"]]>
.png   1U-ha.png (Size: 130.1 KB / Downloads: 809)

.txt   KC868-1U-ha-config.txt (Size: 5.76 KB / Downloads: 434)

esphome:
  name: 1u
  platform: ESP32
  board: esp32dev
 
 
remote_receiver:
  pin: 13
  dump:
    - rc_switch
  tolerance: 50%
  filter: 250us
  idle: 2ms
  buffer_size: 2kb
# Example configuration entry for ESP32
i2c:
  sda: 4
  scl: 16
  scan: true
  id: bus_a
# Example configuration entry
ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO17_OUT
  phy_addr: 0
  # Optional manual IP
 # manual_ip:
 #   static_ip: 192.168.1.199
#    gateway: 192.168.1.1
#    subnet: 255.255.255.0  
# Example configuration entry
pcf8574:
  - id: 'pcf8574_hub_out_1'  # for output channel 1-8
    address: 0x24
  - id: 'pcf8574_hub_in_1'  # for input channel 1-8
    address: 0x22
# Individual outputs
switch:
  - platform: gpio
    name: "light1"
    id: light1
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 0
      mode: OUTPUT
      inverted: true
  - platform: gpio
    name: "light2"
    id: light2
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 1
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light3"
    id: light3
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 2
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light4"
    id: light4
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 3
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light5"
    id: light5
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 4
      mode: OUTPUT
      inverted: true      
     
  - platform: gpio
    name: "light6"
    id: light6
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 5
      mode: OUTPUT
      inverted: true
     
  - platform: gpio
    name: "light7"
    id: light7
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 6
      mode: OUTPUT
      inverted: true
  - platform: gpio
    name: "light8"
    id: light8
    pin:
      pcf8574: pcf8574_hub_out_1
      number: 7
      mode: OUTPUT
      inverted: true
binary_sensor:
  - platform: gpio
    name: "input1"
    on_press:
      then:
        - switch.toggle: light1
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 0
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input2"
    on_press:
      then:
        - switch.toggle: light2
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 1
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input3"
    on_press:
      then:
        - switch.toggle: light3
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 2
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input4"
    on_press:
      then:
        - switch.toggle: light4
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 3
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input5"
    on_press:
      then:
        - switch.toggle: light5
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 4
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input6"
    on_press:
      then:
        - switch.toggle: light6
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 5
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input7"
    on_press:
      then:
        - switch.toggle: light7
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 6
      mode: INPUT
      inverted: true
  - platform: gpio
    name: "input8"
    on_press:
      then:
        - switch.toggle: light8
    pin:
      pcf8574: pcf8574_hub_in_1
      number: 7
      mode: INPUT
      inverted: true
  - platform: remote_receiver
    name: "remoter1"
    rc_switch_raw:
      code: '001111010111001010111000'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light1
    filters:
      - delayed_off: 200ms
  - platform: remote_receiver
    name: "remoter2"
    rc_switch_raw:
      code: '001111010111001010111100'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light2
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter3"
    rc_switch_raw:
      code: '001111010111001010110100'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light3
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter4"
    rc_switch_raw:
      code: '001111010111001010111001'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light4
    filters:
      - delayed_off: 200ms  
   
  - platform: remote_receiver
    name: "remoter5"
    rc_switch_raw:
      code: '001111010111001010110010'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light5
    filters:
      - delayed_off: 200ms
  - platform: remote_receiver
    name: "remoter6"
    rc_switch_raw:
      code: '001111010111001010110101'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light6
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter7"
    rc_switch_raw:
      code: '001111010111001010110001'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light7
    filters:
      - delayed_off: 200ms
     
  - platform: remote_receiver
    name: "remoter8"
    rc_switch_raw:
      code: '001111010111001010110011'
      protocol: 1
    on_press:
      then:
        - switch.toggle: light8
    filters:
      - delayed_off: 200ms
     
# Enable logging
logger:
# Enable Home Assistant API
api:
dallas:
  - pin: 14
    update_interval: 5s
sensor:
  - platform: dallas
    address: 0xa538cee908646128
    name: "1U Temperature"]]> <![CDATA[KC868-1U ESP32 I/O pin define]]> https://www.kincony.com/forum/showthread.php?tid=2998 Wed, 21 Jun 2023 09:21:47 +0800 admin]]> https://www.kincony.com/forum/showthread.php?tid=2998 IIC SCL:16

Relay_IIC_address 0x24

Input_IIC_address 0x22

DS18B20/DHT11/DHT21/LED strip -2: 14

RF433MHz wireless receiver: 13
IR Sender:5
IR Receiver:15

Ethernet (LAN8720) I/O define:

#define ETH_ADDR        0
#define ETH_POWER_PIN  -1
#define ETH_MDC_PIN    23
#define ETH_MDIO_PIN  18
#define ETH_TYPE      ETH_PHY_LAN8720
#define ETH_CLK_MODE  ETH_CLOCK_GPIO17_OUT


RS485:
RXD:32
TXD:33

Buzzer:2]]> IIC SCL:16

Relay_IIC_address 0x24

Input_IIC_address 0x22

DS18B20/DHT11/DHT21/LED strip -2: 14

RF433MHz wireless receiver: 13
IR Sender:5
IR Receiver:15

Ethernet (LAN8720) I/O define:

#define ETH_ADDR        0
#define ETH_POWER_PIN  -1
#define ETH_MDC_PIN    23
#define ETH_MDIO_PIN  18
#define ETH_TYPE      ETH_PHY_LAN8720
#define ETH_CLK_MODE  ETH_CLOCK_GPIO17_OUT


RS485:
RXD:32
TXD:33

Buzzer:2]]>