I had one of this to my master bedroom shutter it is the standard rectangle shape in Egypt from sonoff brand.
It is wifi connect to rf remote or sonoff mobile apps i need to use one app for everything do you able your kincony mobile app work on sonoff wifi? Or do you have touch button 3 position to shutter/ curtain up and down and stop.
Note each floor has 1 circuit 220 volt to all floor shutters and the current control manual rocker switch beside each curtain, it is mandatory to use wifi switch to connect wireless to mobile apos.
Also please tell me how many of this wifi switches can work with confusion and  interruption because i had 12 shutters

Attached Files

Thumbnail(s)
   

What do i need to run Alexa or google voice command to KinCony?
Do i need a certain module for each controller all one for all controllers in the same electric panel?
Assume all my systems are 
KC-868-H32BS with omron relay 250v 16 A
KC-868-H32B with smart buttons

Why the RF remote control 433MHZ not 868 MHZ?
And if i had different wireless system 433 and 868 MHz at the same house , am i able to change the frequency if conflict with other systems ?

I'm new to this system and need to start a new project soon and test that on my house network first.
I had before X10 modules that are 220 volt coil and each module for one circuit single phase with momentary switch, mobile apps and RF remote i had 1 home automation panel that contain all house interior floors lighting load that are coming from 2 sources main and emergency through 3 DB's 
Then finally the automation panel contain the following
1- 2 sources main, emergency 3 phases
2- 3 DBs each are 3 phases
3. All relays are 220 volt coil and distributed each phase and source

If you are trying to replace the system to DC coil 12 volt then you need for each source and single phase a separate AC 220v/ 12 vdc converter
This mean that you need for the automation panel 
3 converters for emergency to present each phase.
6 converters for main 3 for each DB.
Then i need to convert to DC 9 separate converters.
Other wise you will use single phase for emergency as an example phase R convert to DC 12 v and feed all controllers if this phase failed all system will be off.

I really need to know the big reason behind the all system 12 v DC coils !?
And is any way to release version with 220 v AC coil?

You applied free sample KC868-A8 have sent by YANWEN, tracking number is VR445934410YP .

Hope your project goes well and share everyone your achievements.

Is this a possibility to use the open source OpenSprinkler ported firmware ?

https://opensprinkler.com/forums/topic/e...-firmware/

https://github.com/arijav/AriloSprinkler..._dev_esp32

If there is no technical barrier, then I guess the I/O of this board needs to be matched on the OpenSprinkler build I/O ?
Thanks.

esphome:
  name: kc868-a4
  platform: ESP32
  board: esp32dev
 
output:
  - platform: esp32_dac
    pin: GPIO25
    id: dac_output2
  - platform: esp32_dac
    pin: GPIO26
    id: dac_output1

light:
  - platform: monochromatic
    output: dac_output1
    name: "KC868-A4-DAC1"
    gamma_correct: 2
    id: dac_light1
  - platform: monochromatic
    output: dac_output2
    name: "KC868-A4-DAC2"
    id: dac_light2

# Enable logging
logger:

# Enable Home Assistant API
api:

ota:
  password: "3b853165e19b67ba8193c59fe59f21a7"

wifi:
  ssid: "KinCony"
  password: "a12345678"

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Kc868-A4 Fallback Hotspot"
    password: "RgIGz8qo4bVC"

captive_portal:

1: Ethernet work mode = "TCP Server"

controller is a "server", your software is "client".

2: WiFi work mode = "TCP Server"

controller is a "server", your software is "client".

3: Ethernet work mode = "TCP Client"

your software is a "server", controller is "client". when power on, controller will auto connect to your software by ethernet. just "client" will auto connect to "server".

4: WiFi work mode = "TCP Client" instead by MQTT in new firmware

your software is a "server", controller is "client". when power on, controller will auto connect to your software by wifi. just "client" will auto connect to "server".

5: Ethernet work mode = "TCP Client"; WiFi work mode = "TCP Server"

A. your software is a "server", controller is "client". when power on, controller will auto connect to your software by ethernet.

B. controller is a "server", you software is "client".

use one KC868-COL/COLB/COLBS send command to KC868-H32BS, KC868-D8 dimmer controller by RS485 modbus. MAX support 254 devices.

   

Hi,
I just opened and connected by COLB. I am able to visualize the change of status of the DI input ports from the smart board controller app.
I would like to know
1. what is the procedure to update the firmware step by step - I could not find the right thread in the forum, sorry if I missed something
2. I cannot connect to the web interface where to configure the MQTT server - I can only see the interface as attached to this message.

Any help is welcome!

Thanks
Lee

Attached Files

Thumbnail(s)